Mitsubishi MOTION CONTROLLERS Q172DCPU Bedienerhandbuch Seite 142
- Seite / 316
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
6 - 21
6 DRIVE MODULE
6.2.2 Parameter list
The synchronous encoder parameters are shown in Table 6.2 and the parameters
shown in this table are explained in items (1) below.
Refer to the help of MT Developer for the parameter setting method of synchronous
encoder.
Table 6.2 Synchronous Encoder Parameter List
No. Setting item Default value Setting range
1 Synchronous encoder No. —
Q173DCPU : 1 to 12
Q172DCPU : 1 to 8
2 Error-time operation mode Continuation Continuation/ Clutch OFF
(1) Synchronous encoder No.
The synchronous encoder No. is set connected to the Q172DEX/Q173DPX.
Connecting position of Q172DEX/Q173DPX Synchronous encoder No.
P1/E1 1
P2/E2 2
P3/E3 3
P4/E4 4
P5/E5 5
P6/E6 6
P7/E7 7
P8/E8 8
P9/E9 9
P10/E10 10
P11/E11 11
P12/E12 12
P1 to P12: Connect to the Q173DPX.
This is incremental type synchronous encoders.
E1 to E12: Connect to the Q172DEX.
This is absolute synchronous encoder.
REMARK
(Note-1) : The absolute and incremental synchronous encoders can be
used (set) together.
(Note-2) : The synchronous encoder No.1 to 8 are valid in the Q172DCPU.
- Q173DCPU 1
- Q172DCPU 1
- SAFETY PRECAUTIONS 2
- For Safe Operations 3
- 2. For fire prevention 3
- 3. For injury prevention 4
- 4. Various precautions 4
- (4) Wiring 8
- (6) Usage methods 9
- Electro 10
- (10) General cautions 11
- 1. OVERVIEW 18
- (Note-2) : SSCNET: S 19
- 1 OVERVIEW 20
- 2.1 Starting Up the System 22
- MT Developer 23
- Real mode 24
- Virtual mode 24
- 2.3.3 Servo programs 27
- : Used, : Unusable 28
- (1) Internal signals 32
- (2) External signals 32
- 4.1 Internal Relays 34
- (1) Internal relay list 34
- (8) Common device list 41
- 4.1.1 Axis statuses 45
- (8) RLS signal (M2412+20n) 48
- ..….... Command signal 53
- .......…….. Status signal 57
- ...…... Command signal 64
- 4.1.7 Common devices 68
- "0" 70
- .....…..….. Status signal 78
- 4.2 Data Registers 82
- (1) Data register list 82
- (7) Common device list 89
- Feed current value 93
- execution 101
- .......... Command signal 102
- 4.3 Motion registers (#) 104
- 4.5 Special registers (SD) 109
- System Settings 111
- Mounted Not mounted 111
- Unused 0 is stored 111
- Servo amplifier 111
- ........... Monitor device 112
- Faulty SSCNET No 113
- 0 : SSCNET 1 113
- 1 : SSCNET 2 113
- .........….. Monitor device 115
- ..……..…… Command device 115
- 5. MECHANICAL SYSTEM PROGRAM 116
- (1) Block 118
- (2) System 118
- 5.2 Mechanical Module List 120
- 6. DRIVE MODULE 122
- 6 DRIVE MODULE 123
- (Note-3) 124
- (Note-1) 125
- 6.1.2 Parameter list 132
- CAUTION 138
- 6.2.2 Parameter list 142
- (2) Current value change 145
- 7. TRANSMISSION MODULE 148
- Q173DCPU Q172DCPU 149
- (Note-2) 150
- 7 TRANSMISSION MODULE 151
- (1) Gear ratio 151
- 7.2 Clutch 152
- VA, VB : Drive module speed 153
- 7.2.1 Operation 158
- (1) ON/OFF mode 158
- (2) Address mode 159
- (3) Address mode 2 161
- (Note-2) 163
- (5) External input mode 168
- 7.2.2 Parameters 172
- (Note-1), (Note-2) 174
- (Note-3), (Note-4) 174
- (Note-3) 175
- 7.3 Speed Change Gear 181
- 7.3.1 Operation 181
- (Note-1) 182
- Ball screw 186
- Rotary table 186
- 8 OUTPUT MODULE 188
- 8.1 Rollers 190
- 8.1.1 Operation 190
- (1) Operation 190
- (2) Control details 191
- 8.1.2 Parameter list 191
- (1) Output unit 191
- Number of pulses per roller 192
- Roller diameter (L) 192
- Speed limit value 193
- Drive module 194
- Gear(Gear ratio) 194
- Ball screw pitch (P) 195
- Number of pulses per ball 195
- 8.3 Rotary Tables 198
- 8.3.1 Operation 198
- 8.4 Cam 206
- (5) Control details 209
- (6) Control change 209
- (7) Program example 210
- (1) Cam No 211
- (2) Resolution 211
- (4) Operation mode 211
- (5) Cam data table 213
- Number of pulses per cam 215
- (4) Output unit 216
- C-1) [PLS] 219
- C-1) [PLS] in the 219
- 8.4.4 Cam curve list 224
- (1) Parameter list 225
- (2) Operating method 227
- OFF ON even if 1 axis 232
- 9.4 Stop and re-start 236
- (1) Virtual axis stop 236
- <Real mode> 240
- <Virtual mode> 240
- [Real Mode Axis Setting] menu 241
- APPENDIX 1 Cam Curves 246
- PPENDICES 247
- APP - 22 267
- 1 293
- WARRANTY 313
- MOTION CONTROLLER Qseries 314
- (Q173DCPU/Q172DCPU) 314
- MITSUBISHI ELECTRIC 316
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Mitsubishi MOTION CONTROLLERS Q172DCPU
(174 Seiten)
(90 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.104 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern