Mitsubishi F940GOT-LWD-E Technical Information Seite 116
- Seite / 330
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Graphic Operation Terminal F940GOT Other Mode 8
8-6
8.5 ENTRY CODE
When an entry code is registered to the PLC, changes to the set values of timers and counters
in the screen mode and the monitor mode are forbidden. However, the current values can be
changed.
ENTER
Allows to register an entry code to the PLC.
This entry code is shared by other peripheral units. Enter an 8-digit (FX Series) or 6-digit (A
Series) hexadecimal numeric.
INPUT ENTRY CODE: ¡¡¡¡¡¡¡¡
The entered entry code becomes effective when the power of the GOT is turned off, then
turned on again.
DELETE
Deletes the existing entry code.
The existing entry code can only be deleted after it was first been entered in the unit.
UNLOCK
Unlocks temporarily the existing entry code. (The entry code is kept registered.)
The unlock function is valid until the power of the GOT is turned off.
Note:
When you have forgotten the existing entry code, execute "all clear" in a peripheral unit.
However, have in mind that all of the data including programs in the PLC are deleted by
"all clear". It is recommended not to forget the entry code.
u
uu
u
Basic operation
[ ENTRY CODE ] END
ENTER
DELETE
[ ENTRY CODE ]
UNLOCK
[ ENTRY CODE ] END
ENTER
INPUT ENTRY CODE
Screen1 Screen2
0 0 0 0 0 0 0 0
CDEFCLR
89
ENT
B
4567
0123
A
The OTHER MODE
screen is displayed.
ENTRY CODE
Paragraph 8.1
Select "ENTRY CODE"
on the screen.
Screen 1
ENTER 0 to F
Enter an entry
code. Screen 2
ENT
Executes
registration.
DELETE 0 to F
Enter the existing
entry code. Screen 2
ENT
Executes
deletion.
UNLOCK 0 to F
Unlock the existing
entry code. Screen 2
ENT
Executes
unlocking.
- OPERATION MANUAL 1
- GRAPHIC OPERATION TERMINAL 3
- 1. Introduction 15
- 1.2 Function list 18
- 1.3 Format of manual 21
- 1.5 System configuration 23
- Peripheral units of GOT 24
- Programmable controller 25
- Peripheral unit to create 26
- 1.6 Connection of PLC 27
- Baud rate 35
- Data length 35
- Stop bit length 35
- STX CRTransmission data 37
- ETX SumSTX Transmission data 37
- 1 second 41
- 2 seconds 41
- 2. Start up 43
- 3.2 Change of displayed data 57
- 4. HPP Mode 61
- 4.2 PROGRAM LIST 62
- • Input of instruction 64
- Basic operation 65
- 4.3 PARAMETER 71
- 4.4 DEVICE MONITOR 72
- Operation example 75
- 4.5 LIST MONITOR 77
- 4.6 ACTIVE STATE MONITOR 78
- 4.7 BFM MONITOR 79
- 4.8 PC DIAGNOSIS 80
- 5. Sampling Mode 81
- 5.4 CLEAR DATA 91
- 5.5 Control signals in PLC 92
- 6. Alarm Mode 93
- Alarm message 96
- CALL THE PERSON IN CHARGE 99
- PLEASE ADD PARTS 99
- TIME OVER 99
- PRESSURE IS ABNORMAL 99
- 6.4 Alarm history display 101
- 6.5 Alarm frequency display 102
- 6.6 Alarm history clear 103
- 7. Test Mode 105
- 7.2 USER SCREEN 106
- 7.3 DATA BANK 107
- 7.4 DEBUG 108
- 8. Other Mode 111
- MON TUE WED THU FRI SAT 112
- 8.3 DATA TRANSFER 113
- 8.4 PRINT OUT 114
- 8.5 ENTRY CODE 116
- 8.6 SET UP MODE 117
- Creation of Display Screens 9 119
- Key functions 123
- 9.2 Transfer of screen data 126
- 9.4 Concept on screen display 129
- D+0 D+1 D+2 135
- Screen No. -1 -1 Base screen 135
- Details of word devices 143
- Details of write devices 146
- MITSUBISHI 149
- Screen changeover object 151
- 10.2 Registration of object 152
- 10.3 Display objects 153
- Attribute Contents of setting 154
- 10.4 Data display objects 161
- HEATING TIME 166
- PRODUCTION CONTROL 169
- TEMP. HIGH!! 187
- TEMP. NORMAL 187
- 10.5 Data transfer objects 188
- 20 meshes (320 dots) 189
- 12 meshes (240 dots) 189
- Touch key 189
- TEMPERATURE SETTING 197
- 10.6 Text library 207
- 10.7 Image library 208
- 10.8 Data file 209
- Screen changeover 211
- (operation key) or PLC 211
- "Screen No." 216
- (data registers) 219
- S, T or C) becomes ON or OFF 219
- OPERATION 224
- CONTINUOUS 224
- • Sequence program examples 227
- D5C-GOTRE-PACK) 12 230
- 12.2 Figure display function 231
- 12.3 Data display function 232
- Sequence program 238
- GOT screen 238
- MOTOR 1 STOP 241
- 12.4 Graph display function 246
- 12.5 Touch keys 252
- 12.6 Data input function 259
- 12.7 Creation of comment 264
- 12.8 Recipe function 265
- D5C-GOTRE-PACK) 267
- D5C-GOTRE-PACK) 13 268
- Screen No. 10 is displayed 276
- Screen No. 20 is displayed 276
- System information 288
- 14.6 Additional key codes 291
- Table 15.1: 293
- 15.2 Additional key codes 294
- 15.3 Observe status function 295
- 15.7 Creation of key window 305
- Table 16.1: 307
- Table 17.1: 309
- Table 17.2: 309
- Table 17.3: 310
- Table 17.4: 311
- Table 17.5: 311
- Table 17.6: 311
- Table 17.8: 314
- Table 17.9: 314
- Table 17.10: 314
- Table 17.11: 314
- Table 17.12: 315
- Table 17.13: 320
- Table 17.14: 320
- ¨D5C-GOTRE-PACK is used.) 321
- Appendix A:Key code 323
- Appendix B:System Screen No 324
- Appendix C:Key Code List 325
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.797 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern