Mitsubishi FDTC25VD Spezifikationen PDF herunterladen (Seite 83)

'10 • SR-T-091

Installation dimensions

Hanging bolt pitch

Plan

35 35

740

670

455

515

Side

Liquid side pipes

Gas side pipes

Drain hose

(Connection opening diameter ø16)

150

455

236

135

Front

740 106

230 11

Mounting of interconnecting wires (Field wiring)

① Remove the control lid.

②

Connect the connection wire securely to the terminal block.

Preparations for the main frame

Use cables for interconnection wiring to avoid loosening

of the wires.

CENELEC code for cables Required field cables.

H05RNR4G1.5 (Example)

H Harmonized cable type

05 300/500 volts

R Natural-and/or synth. rubber wire insulation

N Polychloroprene rubber conductors insulation

R Stranded core

4 Number of conductors

One conductor of the cable is the earth conductor

(yellow/green)

1.5 Section of copper wire (mm

)

1) Connect the connection wire securely to the terminal

block. If the wire is not affixed completely, contact will

be poor, and it is dangerous as the terminal block may

heat up and catch fire.

2) Take care not to confuse the terminal numbers for

indoor andoutdoor connections.

3) Affix the connection wire using the wiring clamp.

③ Attach the control lid.

Clamp

Control lid

Terminal block

INSTALLATION OF INDOOR UNIT

Drilling of holes in the wall and fixture of sleeve

●

The connecting wires may touch the metal inside the wall and cause danger so it is necessary to

always use the sleeve.

Indoor side

Outdoor side

●

Drill a hole with a 65 whole

core drill.

Sleeve

Wall thickness + 15

(unit : mm)

Sealing plate

Inclination plate

Pipe

Assembled state

φ65

●

When the pipe is connected at the rear, cut off the lower and the right side

portions of the sleeve collar (as shown by the broken line).

Securing the ceiling hanging bolts

If steel embedded ceiling

Inserts

Holed anchor

Holed plug

Hanging bolts M8

Concrete

If wooden ceiling

Holes for ceiling hanging bolts

Square bars for hanging the air conditioner

Clamps

Beams

Secure the ceiling hanging

bolts firmly following the

illustrations and other

instructions.

Installing the main unit

○

Attach the washers and nuts to the ceiling hanging bolts.

○

Attach the hanging tool to the above nuts, and tighten the nuts.

⑧

M8 large washer

M8 nut

M8 handling bolt

M8 nut

(standard accessory)

⑧

M8 large washer

M8 spring lock washer

(standard accessory)

Main frame

Securing the wireless receiver

About the option parts

○

If it is not leveled, the float switch may malfunction or may not start.

Unit main body

Filter guide

Air filter

⑫ Plate (display)

⑩ Flat head

machine screw

Flat head

machine screw

(In the pack of ⑫)

④ Installation frame

③Wireless receiver

Cut off this section if it interferes with the wall.

○

CalkingCalking

Open a through-hole on the wall to install the reception face for the wireless receiver ③.

Insert the wireless receiver ③ in the installation frame ④, and fix the calking section.

Fix the installation frame ④ on the wall using the flat head machine screws ⑩.

Fix the plate (display) ⑫ on the installation frame ④ using the flat head machine screws packed together

with the plate (display) ⑫.

Cut off this section if it interferes

with the wall.

1 2 ... 78 79 80 81 82 83 84 85 86 87 88 ... 110 111

Kommentare zu diesen Handbüchern

Keine Kommentare

Mitsubishi FDTC25VD Spezifikationen Seite 83

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Split-System-Klimaanlagen Mitsubishi FDTC25VD