Mitsubishi FDTC25VD Spezifikationen PDF herunterladen (Seite 70)

'10 • SR-T-091

Necessary tools for the installation work

Q’ty

Option parts

Sealing plate

Sleeve

Inclination plate

Putty

Drain hose (extension hose)

Piping cover

(for insulation of connection piping)

Plus headed driver

Knife

Saw

Tape measure

Hammer

Spanner wrench

Torque wrench

Hole core drill (65mm in diameter)

Wrench key (Hexagon) [4m/m]

Flaring tool set

Gas leak detector

Pipe bender

Gauge for projection adjustment

Used when flare is made by using

conventional flare tool

()

( )

14.0 ~ 61.0N·m

(1.4 ~ 6.1kgf·m)

(

Designed specifically

for R410A

)

Piping in the left direction

Piping in the right rear directionPiping in the left rear direction

Piping in the right direction

INSTALLATION SPACE (INDOOR UNIT)

(FRONT VIEW)

Piping is possible in the rear, left, left rear, left downward, right or downward direction.

Right

Rear

Downward

Left

rear

Left downward

Left

Wireless remote control

Remote control holder

Wood screws



٤ Before installation check that the power supply matches the air conditioner.





Indoor unit

Relation between setting plate and indoor unit

Installing the support of piping

(Install at location that meets the following conditions, after getting approval from the customer)

٤ Where there is no obstructions to the air flow and where the cooled and heated air can be evenly distributed.

٤ A solid place where the unit or the wall will not vibrate.

٤ A place where there will be enough space for servicing. (Where space mentioned below can be secured)

٤ Where wiring and the piping work will be easy to conduct.

٤ The place where receiving part is not exposed to the direct rays of the sun or the strong rays of the street lighting.

٤ A place where it can be easily drained.

٤ A place separated at least 1m away from the television or the radio. (To prevent interference to images and sounds.)

٤ Places where this unit is not affected by the high frequency equipment or electric equipment.

٤ Avoid installing this unit in place where there is much oil mist.

٤ Places where there is no electric equipment or household under the installing unit.

Wireless remote control

In case of piping in the right rear direction

٤ A place where the air conditioner can be received the signal surely during operating the wireless remote control.

٤ Places where there is no affected by the TV and radio etc.

٤ Do not place where exposed to direct sunlight or near heat devices such as a stove.

Sufficient care must be taken not to damage

the panel when connecting pipes.

[Top view]

When drilling the wall that contains a metal lath, wire lath or metal plate, be sure to use pipe hole sleeve sold separately.

• Matters of special notice when piping from left or central/rear of the unit.

Left-hand-side piping Right-hand-side piping

Installation of Installation board

Drilling of holes and fixture of sleeve (Option parts)

Level position (2 locations)

Mating mark for

level surface

Fixing on concrete wall

Use of nut anchor Use of bolt anchor

Shaping of pipings Taping of the exterior

Pipings

Drain hose

Top

Nut

(M6)

Mounting

board

Mounting

board

Max.10

Thickness of the wall + 1.5cm

ø65

Indoor side Outdoor side

Indoor side Outdoor side Installed state

Turn to

tighten

Bolt

(M6 12)

5 cm minimum

from the wall

10 cm minimum

from the wall

Installation board

Sleeve

(sold separately)

6.5 cm minimum from the ceiling

٤ In case of rear piping draw out, cut off the lower

and the right side portions of the sleeve collar.

٤ Drill a hole with whole core drill.

٤ Hold the bottom of the

piping and fix direction

before stretching it and

shaping it.

٤ Tape only the portion

that goes through the

wall.

٤ Always tape the wiring

with the piping.

[Drain hose changing procedures]

1. Remove the drain hose 2. Remove the drain cap.

٤ Remove it with hand or pliers.٤ Remove the screw and drain hose,

making it rotate.

3. Insert the drain cap. 4. Connect the drain hose.

٤ Insert the drain cap which was removed

at procedure “2” securely using a

hexagonal wrench etc.

Note: Be careful that If it is not Inserted

securely, water leakage may occur.

٤ Insert the drain hose securely, making

rotate. And install the screw.

Note: Be careful that If it is not Inserted

securely, water leakage may

occur.

٤ Adjustment of the installation board in the horizontal direction is to

be conducted with four screws in a temporary tightened state.

٤ Adjust so the board will be

level by turning the board

with the standard hole as

the center.

450

Look for the inside wall structures (Intermediats support or pillar

and firmly install the unit after level surface has been checked.)

Standard

hole

Piping for Liquid (20 to 50 type) : ø6.35

Piping for Gas (20 to 35 type) : ø9.52

(50 type) : ø12.7



Completely seal the hole on

the wall with putty. Otherwise,

furniture, or other, may be

wetted by leaked water or

dewing.

putty

Q’ty

Standard accessories (Installation kit)

Accessories for indoor unit

Installation board

(Attached to the rear of the indoor unit)

Wireless remote control

Remote control holder

Battery [R03 (AAA, Micro) 1.5V]

Air-cleaning filters

Filter holders

(Attached to the front panel of indoor unit)

Insulation (#486 50 x 100 t3)

Tapping screws

(for installation board ø4 X 25mm)

Wood screws

(for remote control switch holder ø3.5 X 16mm)

()

Designed specifically

for R410A

Space for service Space for service

Indoor unit

Installation board

Piping hole (ø65)

Drain hose (ø16)

Piping for Liquid

Piping for Gas

Piping hole (ø65)

Space for service

48.947

139 450 209

106.5 585 106.5

50 100

7.2 7.7279.1

4715 Space for service

531.8

471.6

403.6

Indoor side Outdoor side

1 2 ... 65 66 67 68 69 70 71 72 73 74 75 ... 110 111

Kommentare zu diesen Handbüchern

Keine Kommentare

Mitsubishi FDTC25VD Spezifikationen Seite 70

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Split-System-Klimaanlagen Mitsubishi FDTC25VD