Mitsubishi SC-SL2NA-E Spezifikationen PDF herunterladen

’10 • SC-T-154

1 CENTRAL CONTROL SC-SL2N-E

(1) Speciﬁcation

Deﬁnitions of new and previous Super Link (new and previous SL)

New Super Link (new SL): All units connected to the network are models compatible with New Super Link

(KXE6 model or later models. Central controller and I/F are from “N” models.) and

SL setting is unchanged from shipment (“New” or “AUTO”).

Previous Super Link (previous SL): Units do not meet the conditions of New SL. When even a single unit connected to

the network is an earlier model than KXE4 or the connected model is not compatible

with New SL. Setting explained in Note (5) is required.

Appearance

Notes (1) Some of functions may not be used depending on the indoor unit. (See page 4 (2).)

(2) For the specification of relay being procured at site, select a product that can assure the minimum application load of DC 12 V, 10 mA or less.

Even if it is reset within 2 minutes after input, the input state is retained.

(3) For the specification of relay being procured at site, select a product with the rated voltage at DC 12 V, max. power consumption at DC 0.9 W or

under (80 mA or under).

(4) Dimension +35 in ( ) indicates the embedded dimension.

(5) When the connecting network consists of previous Super Link, it is necessary to set the control selector switch SW5 to OFF.

(Factory default is ON.)

Description

Model name

Applicable model

Ambient temperature in operation

Power supply

Power consumption

External dimensions (HWD)

Net weight

Max. number of connectable indoor units

CENTRAL CONTROL SC-SL2NA-E

SC-SL2NA-E

Super Link compatible indoor unit

(1)

0 ~ 40˚C

1 phase, 100 ~ 240 V, 50/60 Hz

120mm215mm(2535)mm

(4)

1kg

New SL: Max. 64 units, previous SL: Max. 48 units

1 point, Non-voltage contact “a” input

(Open

Close: RUN, Close

Open: STOP)

1 point, Non-voltage contact point “a” input,

continuous input

(Close; Center & Stop all units)

1 point, Non-voltage contact “a” input,

continuous input

(Close: Center & Fan mode)

All indoor units at STOP; Open

If there is any unit operating; Close

All indoor units normal: Open

If there is any abnormal unit; Close

Input

Output

External timer input

(2)

Emergency stop signal input

(2)

Demand signal input

(2)

Operation output

(3)

Error output

(3)

PJZ000Z281

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - 1 CENTRAL CONTROL SC-SL2N-E

- 2 -’10 • SC-T-1541 CENTRAL CONTROL SC-SL2N-E(1) SpeciﬁcationDeﬁnitions of new and previous Super Link (new and previous SL) New Super Link (new S

Seite 2 - ’10 • SC-T-154

- 3 -’10 • SC-T-154CENTER / REMOTE displayDisplays which is in effect, the central control or the local remote controllers.PROGRAM SET displayDisplaye

Seite 3 - (3) Status monitor

- 4 -’10 • SC-T-154Notes (1) Don’t use the auto mode on any indoor unit other than those connected to the simultaneous heating & cooling 3-pipe s

Seite 4 - (4) Program setting

- 5 -’10 • SC-T-154Item DescriptionGroup settingIndividual settingTime & date settingAlarm historyDemand controlEmergency stopPower restoration co

Seite 5 - (8) Electrical wiring

- 6 -’10 • SC-T-154(7) Installation procedure(a) In case of embedding in a wall, ﬁrst, embed the power supply wire, signal wire, and electrical box.

Seite 6 - (9) Installation work

- 7 -’10 • SC-T-154Wiring OutlineWiring specifications(9) Installation workPlease install the central control after turning off the power for fear of

Seite 7 - 1 2 3 4 5 6 7 8 9 10 11 12

- 8 -’10 • SC-T-154(c) In case of installing on the control boardPlease be sure to lock the control board to protect persons from the electric shock.

Seite 8

- 9 -’10 • SC-T-154(10) Control switch selectionIt is possible to change the setting as follows by settings of the PCB switches SW1 to SW10, J1, J2,

Weitere Dokumente für Aufnahmegeräte Mitsubishi SC-SL2NA-E

Um das Dokument anzuzeigen Mitsubishi SC-SL2NA-E Bedienungsanleitung

Mitsubishi SC-SL2NA-E Bedienungsanleitung (40 Seiten)

Um das Dokument anzuzeigen Mitsubishi SC-SL2NA-E Installationshandbuch

Mitsubishi SC-SL2NA-E Installationshandbuch (20 Seiten)

Um das Dokument anzuzeigen Mitsubishi SC-SL2NA-E Spezifikationen

Mitsubishi SC-SL2NA-E Spezifikationen (37 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Mitsubishi SC-SL2NA-E Spezifikationen

Stöbern Sie online oder laden Sie Spezifikationen nach Aufnahmegeräte Mitsubishi SC-SL2NA-E herunter. Mitsubishi SC-SL2NA-E Specifications [en] [it] Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Aufnahmegeräte Mitsubishi SC-SL2NA-E

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Aufnahmegeräte Mitsubishi SC-SL2NA-E