Mitsubishi PURY-RP300YJM-A Installationshandbuch PDF herunterladen (Seite 11)

6. Space required around unit

1 In case of single installation

Secureenoughspacearoundtheunitasshowninthegureonpage2.

[Fig. 6.0.1] (P.2)

<A> Top view <B> Side view

<C> When there is little space up to an obstruction

Front

Unit

height

Back

Air

outlet guide (Procured at the site)

(1) If the distance is 300 mm or more between the rear side and the wall

(2) If the distance is 100 mm or more between the rear side and the wall

(3) If the wall height (H) of the front, rear or side exceeds the wall height

restriction

When

the height of the walls on the front, back or on the sides <H> exceeds

thewallheightlimitasdenedhere,addtheheightthatexceedstheheight

limit<h>totheguresthataremarkedwithanasterisk.

•

all

height limit> Front: Up to the unit height

Back: Up to 500 mm from the unit bottom

Side: Up to the unit height

(4) If there are obstacles at the upper part of the unit

2 In case of collective installation

[Fig.

6.0.2] (P.2)

Front

Must be open

Wall

height (H)

When multiple units are installed adjacent to each other, secure enough

space to allow for air circulation and walkway between groups of units as

shownintheguresonpage2.

At least two sides must be left open.

As with the single installation, add the height that exceeds the height limit

<h>totheguresthataremarkedwithanasterisk.

If there is a wall at both the front and the rear of the unit, install up to 6 units

consecutively in the side direction and provide a space of 1000 mm or more

as inlet space/passage space for each 6 units.

•

[Fig.

7.0.1] (P.2)

Use suspension ropes that will withstand the weight of the unit.

When moving the unit, use a 4-point suspension, and avoid giving impacts

to the unit (Do not use 2-point suspension

Place

protective pads on the unit where it comes in contact with the ropes to

protect the unit from being scratched.

Set the angle of roping at 40° or less.

Use 2 ropes that are each longer than 8 meters.

•

Place

protective padding at the corners of the product to protect the product

from scratches or dents that might be caused by the rope.

Caution:

Be very careful when carrying/moving the product.

- Wheninstallingtheoutdoorunit,suspendtheunitatthespeciedlocationof

the unit base. Stabilize as necessary so that it does not move to the side and

support it at 4 points. If the unit is installed or suspended with 3-point support,

the unit may become unstable and fall.

•

7. Lifting method

3. Combination of outdoor units

The unit described in this manual cannot be used in combination. It is designed to be used as a single unit.

Outdoor unit model Component unit model

PURY-RP200YJM-B(-BS) - -

PURY-RP250YJM-B(-BS) - -

PURY-RP300YJM-B(-BS) - -

4. Specications

Model

PURY-RP200YJM-B PURY-RP250YJM-B PURY-RP300YJM-B

Noise level (50/60Hz)

56dB <A> 57dB <A> 59dB <A>

External static pressure

0 Pa *2

Indoor units

Total capacity

50~150% *1

Model

15~250

Quantity

1~20 1~25 1~30

Operation

temperature

Standard

type

Cooling mode: – 5°CDB ~ 43°CDB

Heating mode: – 20°CWB ~ 15.5°CWB

Fresh air intake type

Cooling mode: 21°CDB ~ 43°CDB

Heating mode: – 12.5°CWB ~ 20°CWB

*1: The total indoor capacity of units run simultaneously is 150% or less.

*2: To enable high static pressure with RP200, RP250, RP300, set the DipSW on the main panel as follows.

SW3-9: ON, SW3-10 60Pa compatible: OFF, 30Pa compatible: ON

5. Conrmation of parts attached

This unit includes the following parts. Please check.

For usage methods, refer to item 10.2.

1 Connecting pipe

ID ø25.4, ID ø28.58

<Low-pressure side>

Model RP200 1 pc.

RP250 1

pc.

RP300 1

pc.

•

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 19 20

Kommentare zu diesen Handbüchern

Keine Kommentare

Mitsubishi PURY-RP300YJM-A Installationshandbuch Seite 11

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Split-System-Klimaanlagen Mitsubishi PURY-RP300YJM-A